2021 Engineering Literacy II a

Font size  SML

Register update notification mail Add to favorite lecture list
Academic unit or major
School of Engineering
Sampei Mitsuji  Okutomi Masatoshi  Imura Jun-Ichi  Nakao Hiroya  Tsuchida Takahiro  Kuramoto Akisue  Sugahara Yusuke  Kim Joon-Wan  Nakanishi Hiroki  Hijikata Wataru  Kurabayashi Daisuke  Manaka Takaaki 
Class Format
Lecture / Exercise     
Media-enhanced courses
Day/Period(Room No.)
Course number
Academic year
Offered quarter
Syllabus updated
Lecture notes updated
Language used
Access Index

Course description and aims

This course aims to become a bridge between general education at high school and specialized education in the subjects of No.200 or higher. This course also aims to cultivate not only basic knowledge of engineering but also sense and attitude for problem solving so that the freshmen of School of Engineering can learn actively specialized subjects after sophomore.
By taking all Engineering literacy I-IV, the students experience the following all seven subjects in Engineering Literacy.
【Manufacturing process 】
【Mechanical Design (Steamship)】
【Mechanical Design (CAD)】
【Wireless electric car with microcomputer】
【Communication, Computation, and Intelligent Information Processing】
【Management Technology (Industrial Engineering and Economics)】

Student learning outcomes

By completing this course, students will be able to:
1) understand the basic principle of measurement by sensors.
2) understand the basic principle of feedback control.
3) master the design method of control systems.
【Mechanical Design (CAD)】
1) carry out structural and frequency analysis of mechanical parts with CAE.
2) create 3D model of mechanical parts in 3D CAD.
3) design mechanical parts using CAD and CAE.


Measurement, Control, System
【Mechanical Design (CAD)】
CAD(Computer Aided Design), CAE(Computer Aided Engineering,)

Competencies that will be developed

Specialist skills Intercultural skills Communication skills Critical thinking skills Practical and/or problem-solving skills

Class flow

This course introduces the basic principle of feedback control using the signal measured by sensors, and holds a competition to help them to understand the effectiveness using the line tracing car.
【Mechanical Design (CAD)】
Through this course, students can learn fundamental basics of CAD (Computer Aided Design) and CAE (Computer Aided Engineering) by using Inventor, a tool for CAD. The first half of this lecture shows how to use CAE and CAD. The latter half of the lecture is a design competition using CAE and CAD.

Course schedule/Required learning

  Course schedule Required learning
Class 1 Introduction: Aim of the course, notice for students, setup of computer systems. A student should have an overlook of the course and set up his/her computer system for the course.
Class 2 Measurement, sensor, and collision avoidance Understand how sensors work and how collision can be avoided.
Class 3 Design control system for line tracing Carry out the design of control system for line tracing.
Class 4 Competition: Evaluation and Award Ceremony Evaluate the performance of the control through the line tracing competition.
Class 5 Introduction of CAD Make 3D structure models by using Inventor.
Class 6 ・FEM (Finite Element Method) Analysis ・3D Design competition 1 (Create a 3D model) ・Carry out structural and frequency analyses by using Inventor. ・Create 3D model of mechanical parts and carry out the structure and frequency analyses for them in Inventor.
Class 7 3D Design competition 2 (Improve properties of the 3D model) Improve the specified property of the model under the given constraint and propose a final model.

Out-of-Class Study Time (Preparation and Review)

To enhance effective learning, students are encouraged to spend approximately 100 minutes preparing for class and another 100 minutes reviewing class content afterwards (including assignments) for each class.
They should do so by referring to textbooks and other course material.


None required

Reference books, course materials, etc.

Documents will be distributed

Assessment criteria and methods

Evaluate the report and the result of the competition.
【Mechanical Design (CAD)】
Evaluate the design report and the result of the competition.

Related courses

  • XEG.B101 : Engineering Literacy I
  • XEG.B102 : Engineering Literacy II
  • XEG.B103 : Engineering Literacy III
  • XEG.B104 : Engineering Literacy IV

Prerequisites (i.e., required knowledge, skills, courses, etc.)

This lecture is only for the freshmen of School of Engineering.
Students are strongly recommended to take all Engineering literacy I-IV to experience all subjects in Engineering Literacy.

Page Top